This is an additional post that has all my parts list and more pictures for my recent upgrade build. I split it up so it wouldn’t be so long.
Here’s the original post:
Here’s the parts list for each upgrade.
Upgrade size to 1000x1000
#1 - MakerSlide - 25142-11
Description: Length: 1000mm, Type: MakerSlide, Color: Black Anodized, Ends: Tapped M5
Quantity: 2
#2 - Aluminum Extrusion (20mm x 20mm) - Clear - 26047-02
Description: Finish: Clear Anodized, Height: 20 mm, Length: 1000 mm, Width: 20 mm, Type: Extrusion, Color: Gray
Quantity: 5
#3 - Product: Wide MakerSlide - 30678-03
Description: Length: 1000mm, Ends: Tapped M5, Color: Black
Quantity: 1
#4 - 100ft 22/2 AWG Stranded Shielded wire for limits and probe
#5 - 1 meter Drag Chain
#6 - Reused old 500x500 drag chains by combining them together and custom making drag chain mounts from old hardware
#7 - Aluminum bar stock for custom drag chain brackets and Y axis stiffening brackets
https://www.amazon.com/gp/product/B075ZY2VQ5/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
#8 - Gussets for excrusion connections and mounting to table
#9 - Pre-assembly nuts
#10 - M5x8mm Screws
#11 - Reused short aluminum extrusions from 500x500 for x axis drag chain support by combining them both together with aluminum bracket
#12 - 50ft 18/4 Wire for steppers
https://www.ebay.com/itm/50-FEET-18-4-AWG-SHIELDED-STRANDED-WIRE-CABLE-CNC-STEPPER-MOTOR-Servo-Alarm-FT/273027022220?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
Replaced gShield with ST6600 drivers
#1 - Four (4) ST6600 drivers
Auto start spindle and shop vac
#1 - Two (2) Relays - 1 for spindle and 1 for shop vac
Custom enclosure (Lots of wiring stuff)
#1 - USB extension
#2 - Heat shrink
#3 - Fork terminals for 18-22ga
#4 - Screw shield for Uno board
#5 - 5pin Aviator connectors
#6 - Two (2) 24v Fans - (Reuse old fan as third fan)
#7 - Terminal connectors
#8 - Two (2) pack Barrier strips
#9 - Panel power plugs
#10 - 4 pin aviation connectors
Upgraded motors from Nema 17 to Nema 23 (269oz)
#1 - 3 pack Nema 23
#2 - Single for z axis (exact same as others)
Upgraded belts from 6mm width/2mm pitch to 9mm width/3mm pitch
#1 - 4 meters of 9mm wide 3mm pitch belts
https://www.ebay.com/itm/GT-Arc-3GT-Open-Synchronou-Timing-Belt-Width-3-6-9-15mm-Neoprene-Small-Backlash/221937443133?ssPageName=STRK%3AMEBIDX%3AIT&var=520826521443&_trksid=p2057872.m2749.l2649
#2 - Three (3) 20T 3mm pitch pulleys w/ 6.35mm bore
#3 - Six (6) 9mm smooth idler pulleys
#4 - @PhilJohnson 9mm wide belt end clips
http://www.designsbyphil.com/9mm-end-clips.html
Upgraded z-axis to CNC4Newbie1’s 6" linear rail
#1 - Linear rail
SuckIt dust boot
Button panel
#1 - 110v Power indicator
#2 - Push Buttons (had to buy 5 packs to get colors and turn around times I wanted)
#3 - Switches - (2 way and 3 way)
**#4 - E-Stop (Kind of small, would get bigger one)
LED lights
#1 - LEDs
#2 - LED DC voltage regulator (LEDs inside enclosure)
#3 - 12v LED power supply for table lights
Wireless Keyboard Pendant
#1 - Keypad
https://www.amazon.com/gp/product/B072HTCJ3V/ref=od_aui_detailpages01?ie=UTF8&psc=1
